IFD 100 fuel data block

Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic

   the two fuel data blocks appear on my IFD 100 but do not display any data.  My IFD 540 present the correct data but it appears not to transfer over to the IFD 100.  Everything else works great.  Any ideas as to what might be preventing the transfer of data?

Author	Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic
Froethel Members Profile Send Private Message Find Members Posts Add to Buddy List Groupie Joined: 02 Apr 2016 Location: Selden, NY Status: Offline Points: 54	Post Options Post Reply Quote Froethel Report Post Thanks(0) Quote Reply Topic: IFD 100 fuel data block Posted: 19 Aug 2018 at 3:36pm
	the two fuel data blocks appear on my IFD 100 but do not display any data. My IFD 540 present the correct data but it appears not to transfer over to the IFD 100. Everything else works great. Any ideas as to what might be preventing the transfer of data?
	Frank

edanford Members Profile Send Private Message Find Members Posts Add to Buddy List Senior Member Joined: 21 Nov 2011 Location: Austin Tx Status: Offline Points: 116	Post Options Post Reply Quote edanford Report Post Thanks(0) Quote Reply Posted: 19 Aug 2018 at 4:56pm
	I think the data transfer quit with the 10.2 SW version release of IFD100 I was using it just fine until then. I have had no data since then
	Ed

AviSteve Members Profile Send Private Message Find Members Posts Add to Buddy List Admin Group Joined: 12 Feb 2018 Location: Melbourne, FL Status: Offline Points: 2246	Post Options Post Reply Quote AviSteve Report Post Thanks(0) Quote Reply Posted: 19 Aug 2018 at 8:23pm
	See the thread at http://www.avidynelive.com/fuel-time-remaining-not-displayed-on-ifd_topic1549.html. Is that what you're describing? If so, I recommended manually setting initial fuel on the IFD100, but never heard back whether that worked. Give it a shot and post back the results.
	Steve Lindsley Avidyne Engineering

edanford Members Profile Send Private Message Find Members Posts Add to Buddy List Senior Member Joined: 21 Nov 2011 Location: Austin Tx Status: Offline Points: 116	Post Options Post Reply Quote edanford Report Post Thanks(0) Quote Reply Posted: 20 Aug 2018 at 11:31am
	I am talking about fuel flow or any related fuel data. (Fuel used etc) It was working fine until the IFD100 was upgraded to 10.2 My IFD540 shows all this data perfectly but does not show data on IFD100 even though fields are there. Ed
	Ed

Randy Members Profile Send Private Message Find Members Posts Add to Buddy List Groupie Joined: 20 Jul 2016 Location: KTUS Status: Offline Points: 74	Post Options Post Reply Quote Randy Report Post Thanks(0) Quote Reply Posted: 10 Sep 2018 at 5:30pm
	Steve, I would have replied earlier, but somehow got lost in the internet system... Anyway... ---------------------------------------------------------------------------------- The fuel line, in the DTK, TKDIST AT, ETE, (to waypoint information, in datablock options,) in flight, ops normal. -------------------------------------------------------------------------------------- The fuel block in the AUX, UTIL, CALCULATORS, FUEL PLANNER, FUEL ON BOARD, ops normal, (even after shut down of the IFD440) It stays in memory. The fuel numbers can be reset on this page, to any number. (unknown if it will reset back to remaining fuel) --------------------------------------------------------------------------- The fuel block in AUX, SYS, FUEL MGMT, shows proper flow, remaning time, and econ, (from shadin unit) during flight only. After shutdown, all of the blocks are blank/filled with three (3) dashes. Unable to insert anything in the AUX, SYS, FUEL MGMT, blocks at any time.
	Regards, Randy