Avidyne Homepage
Forum Home Forum Home > Avidyne General > SkyTrax Series ADS-B Receivers & Transceivers
  New Posts New Posts RSS Feed - IFD540 / MLB100 traffic range
  FAQ FAQ  Forum Search   Register Register  Login Login

IFD540 / MLB100 traffic range

 Post Reply Post Reply
Author
Message
edanford View Drop Down
Senior Member
Senior Member
Avatar

Joined: 21 Nov 2011
Location: Austin Tx
Status: Offline
Points: 116
Post Options Post Options   Thanks (0) Thanks(0)   Quote edanford Quote  Post ReplyReply Direct Link To This Post Topic: IFD540 / MLB100 traffic range
    Posted: 29 Oct 2015 at 12:20pm
What nM range from my position does ADSB traffic display on IFD540 main screen?

I know the sidebar icon is 2 or 6 nm

I would like to see ADSB traffic within 15 nm of my position on moving map as that may change my altitude / direction of flight.

Is this a feature that might be programmable in future SW release?
Ed
Back to Top
DavidBunin View Drop Down
Senior Member
Senior Member
Avatar

Joined: 20 May 2015
Location: Rockwall, TX
Status: Offline
Points: 742
Post Options Post Options   Thanks (0) Thanks(0)   Quote DavidBunin Quote  Post ReplyReply Direct Link To This Post Posted: 30 Oct 2015 at 8:25am

Not sure I understand the question. If I put the thumbnail into UNRESTRICTED mode, then I can see traffic very far away on the main screen. Easily 30 or 40 miles away.

To adjust the thumbnail range, tap the upper half of the icon.  To adjust the mode, tap the lower part of the icon.

What ADS-B Out device are you using to stimulate the network?  Does your ADS-B Out device "advertise" that you only receive data on the UAT frequency?

David Bunin

Back to Top
edanford View Drop Down
Senior Member
Senior Member
Avatar

Joined: 21 Nov 2011
Location: Austin Tx
Status: Offline
Points: 116
Post Options Post Options   Thanks (0) Thanks(0)   Quote edanford Quote  Post ReplyReply Direct Link To This Post Posted: 30 Oct 2015 at 12:00pm
Hi David,

  The question is similar to foreflight ADSB traffic filter option   i.e.   can I filter traffic at a range that I choose?

  I don't want to clutter my screen with traffic that will have no effect on my flight but do want to see something that might affect me in 5 minutes (roughly everything within 15 nm)

  I did not get my MLB100 working for traffic until Tuesday and I have not seen any configuration options on map configuration page
Ed
Back to Top
roltman View Drop Down
Senior Member
Senior Member


Joined: 04 Aug 2011
Status: Offline
Points: 173
Post Options Post Options   Thanks (0) Thanks(0)   Quote roltman Quote  Post ReplyReply Direct Link To This Post Posted: 30 Oct 2015 at 12:03pm
Ed,

Using the traffic thumbnail you can filter the "above/below/normal/unrestricted" and it will update what's shown on the map.

Changing the thumbnail range had no affect on what was displayed on the map.
Back to Top
edanford View Drop Down
Senior Member
Senior Member
Avatar

Joined: 21 Nov 2011
Location: Austin Tx
Status: Offline
Points: 116
Post Options Post Options   Thanks (0) Thanks(0)   Quote edanford Quote  Post ReplyReply Direct Link To This Post Posted: 30 Oct 2015 at 1:28pm
I get that

Question is on ability for filter out traffic on map that is outside a specific nm range from my location
Ed
Back to Top
DavidBunin View Drop Down
Senior Member
Senior Member
Avatar

Joined: 20 May 2015
Location: Rockwall, TX
Status: Offline
Points: 742
Post Options Post Options   Thanks (0) Thanks(0)   Quote DavidBunin Quote  Post ReplyReply Direct Link To This Post Posted: 30 Oct 2015 at 2:43pm

Other than the toggle between the "normal range" options and the "unrestricted" option, I am not aware of any way to control the range limit displayed on the IFD.

David Bunin

Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 12.01
Copyright ©2001-2018 Web Wiz Ltd.

This page was generated in 0.172 seconds.