"VNAV Suspended"

Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic

   IFD 540: I have just started having a problem with intercepting an RNAV approach, specifically the vertical nav (glideslope).  Using a Garmin 500 autopilot.  When I am close to the final approach course, I'm getting a "VNAV Suspended" message, and the autopilot does not capture the decent path.  Software level 10.3.1.2.

This is a new problem... it's worked just fine in the past.  Can't think of any changes which might have made any difference. 

Author	Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic
frankbell Members Profile Send Private Message Find Members Posts Add to Buddy List Senior Member Joined: 16 Jan 2015 Location: NC Status: Offline Points: 113	Post Options Post Reply Quote frankbell Report Post Thanks(0) Quote Reply Topic: "VNAV Suspended" Posted: 5 hours 39 minutes ago at 10:18am
	IFD 540: I have just started having a problem with intercepting an RNAV approach, specifically the vertical nav (glideslope). Using a Garmin 500 autopilot. When I am close to the final approach course, I'm getting a "VNAV Suspended" message, and the autopilot does not capture the decent path. Software level 10.3.1.2. This is a new problem... it's worked just fine in the past. Can't think of any changes which might have made any difference.

dmtidler Members Profile Send Private Message Find Members Posts Add to Buddy List Senior Member Joined: 12 Feb 2016 Location: USA Status: Offline Points: 634	Post Options Post Reply Quote dmtidler Report Post Thanks(0) Quote Reply Posted: 5 hours 13 minutes ago at 10:44am
	According to the IFD540 PG, "VNAV Suspended" (and "VNAV Terminated") advisory messages only relate to Enroute VNAV operations being suspended or terminated due to various conditions. This should not affect RNAV GPS approach vertical guidance. I have a similar setup with a couple of G5's and a GFC500 autopilot. The autopilot will not follow the IFD540 Enroute VNAV vertical guidance; however, will capture and follow RNAV GPS approach vertical guidance when the GFC500 APR mode is armed/active. BTW - in my experience, it is normal for the "VNAV Suspended" advisory message to appear when the IFD540 transitions from enroute VNAV to approach vertical guidance. Edited by dmtidler - 5 hours 7 minutes ago at 10:50am

frankbell Members Profile Send Private Message Find Members Posts Add to Buddy List Senior Member Joined: 16 Jan 2015 Location: NC Status: Offline Points: 113	Post Options Post Reply Quote frankbell Report Post Thanks(0) Quote Reply Posted: 4 hours 15 minutes ago at 11:42am
	"should not affect RNAV GPS approach vertical guidance...", but apparently it does. Not using enroute VNAV.

dmtidler Members Profile Send Private Message Find Members Posts Add to Buddy List Senior Member Joined: 12 Feb 2016 Location: USA Status: Offline Points: 634	Post Options Post Reply Quote dmtidler Report Post Thanks(0) Quote Reply Posted: 3 hours 19 minutes ago at 12:38pm
	Keep in mind, if Enroute VNAV is enabled on your IFD Main System Config page and your active approach has any stepdown fixes outside of the FAF, then until passing the last stepdown point or the FAF becomes the active waypoint, Enroute VNAV is being used. It appears by your description that Enroute VNAV is enabled on your IFD's Main System Config page because the "VNAV Suspended" advisory would not appear if Enroute VNAV was disabled.

frankbell Members Profile Send Private Message Find Members Posts Add to Buddy List Senior Member Joined: 16 Jan 2015 Location: NC Status: Offline Points: 113	Post Options Post Reply Quote frankbell Report Post Thanks(0) Quote Reply Posted: 1 hour 22 minutes ago at 2:35pm
	Scenario: I first encountered this on a VFR flight where the destination airport was unexpectedly IMC. So with no flight plan, I simply entered the approach and went direct the IAF (with clearance, of course!). Did not get the "suspended" message that time, but the autopilot didn't capture the glideslope, and I flew it manually. Then went out to reenact the scenario at my home airport (KAVL), to try to figure out what happened. No flight plan in the 540, just a radar vectors to the RNAV 35, and on three tries, got the "suspended" message three times. I don't understand! It's worked fine in the past...